Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCWS Door Installation: The Miami Gardens Owner’s Guide
We stock and install CWS-compatible door hardware and replacement parts throughout Miami Gardens, with most installations running between $340 and $1,100 depending on the specific part and your door model. We keep the most common CWS failure points on our trucks, so a technician can usually complete the work in one trip. Most homeowners discover the problem when the door starts dragging across the threshold, the multi-point lock resists turning, or they notice a fogged glass insert that wasn’t there last hurricane season. By the time a CWS door acts up in our humidity, the part has usually been wearing down for a while.
Which CWS Models This Applies To
CWS produces residential entry doors and patio systems under several series lines, and the part compatibility is not universal between them. The hardware that fits a CWS Classic entry door will not necessarily match a CWS architectural series or their newer impact-rated lines. The surest way to identify what you have is to check the hinge-side edge of the door slab for an etched label or a sticker near the bottom corner. If that’s worn off, we measure the slab thickness, the hinge spacing, and the lock bore pattern on site.
For CWS doors specifically, the industry standard deadbolt prep is 2-1/8 inches, but some CWS models use a wider multi-point lock cassette that takes a taller faceplate. We’ve also run into CWS doors with non-standard roller diameters on their sliding lines that a generic replacement roller will not seat correctly. That’s the kind of mismatch that causes a homeowner to buy a part twice. When OEM CWS parts are available, we quote them first. When lead times are long or a part has been discontinued, we’ll recommend a quality aftermarket equivalent and show you both options on paper before anything is ordered.
Signs Your CWS Door Installation Is Failing
- The door drags or binds when you open or close it. In Miami Gardens, this is usually a worn hinge or roller, not a “settling house.” The hardware has lost tolerance against the frame and needs to be replaced, not adjusted again.
- The multi-point lock turns hard or only half-engages. The locking rods and gearbox inside CWS multi-point hardware collect fine dust and corrosion over time. Once the gearbox strips, no amount of lubricant brings it back.
- You see daylight around the sweep or weatherstripping. This means the door slab has sagged just enough to open a gap. In our humidity, that gap becomes the path for water intrusion during afternoon storms.
- The handle feels loose even after tightening the visible screws. The internal spindle or the backing plate has worn out. On CWS hardware, this is one of the most common failures we replace.
- Glass inserts show fog between the panes. The sealed unit has failed. That’s a glass replacement job, not a cleaning issue, and it will not resolve on its own in Florida weather.
Replacement Cost & What’s Included
For Miami Gardens homeowners, CWS door part replacement and installation typically falls between $340 and $1,100 installed. A basic deadbolt and handle swap lands at the lower end. A full multi-point lock assembly with new hardware runs higher, and a replacement glass insert for a CWS door can push toward the upper end depending on size and whether it’s impact-rated.
| Service | Installed Price Range |
|---|---|
| CWS door handle / lockset replacement | $340 - $520 |
| CWS multi-point lock assembly | $620 - $1,100 |
| CWS door hinge / roller replacement (per opening) | $290 - $480 |
| CWS glass insert replacement (sealed unit) | $450 - $900 |
Every estimate is line-item, parts and labor shown separately, and the number we quote is the number you pay. The work is covered by our Done Right Promise, and we register the part warranty in writing before the truck leaves your driveway. If you’re 55 or older or a veteran, the 5% discount applies to this work.
DIY or Call Us?
There are things worth checking yourself. You can tighten visible screws on the handle plate. You can clean the track on a sliding CWS door and see if the rollers are spinning freely. You can note where the door binds and whether the lock engages smoothly. Those observations help us quote the job more accurately over the phone.
What we do not recommend is pulling a CWS multi-point lock assembly apart on your own. The locking rods run through the full height of the slab, and the gearbox is under load when the door is shut. If a rod slips out of alignment mid-repair, you can wind up with a door that won’t open or close at all, which is a far worse problem than the one you started with. Same goes for glass inserts on impact-rated CWS doors: the sealed unit is heavy, the glazing tolerances are tight, and a dropped corner means a shattered pane and a bigger bill. Let a trained technician handle it. Call (386) 516-5343 and we’ll get someone out to look at it properly.
FAQs
Realistically, CWS door hardware lasts 8 to 15 years in our coastal humidity and heat before the springs, rollers, and lock cassettes start needing replacement. Multi-point lock gearboxes are typically the first component to go, usually between years 8 and 12. Moisture and salt air accelerate wear, so doors that face west get more sun damage to finishes while doors that catch the afternoon storms age faster on seals and hardware. Call (386) 516-5343 if your door is in that age range and acting up, and we’ll give you an honest read on what’s left in it.
Sometimes, but not as often as people hope. A loose handle can often be tightened and adjusted. A stripped gearbox, a warped hinge, or a blown sealed unit cannot be repaired in any way that lasts, and we won’t charge you for a repair that buys six weeks. When repair is viable, that’s what we recommend. When it isn’t, we’ll show you why and give you the replacement price before we do anything.
Most handles, hinges, and lock assemblies take between one and two hours with a technician who knows the hardware. A glass insert replacement can run longer because the glazing compound needs time to set before the door is fully functional. Since we carry the most common CWS parts on the truck, there’s usually no second appointment. If your part isn’t on the truck, we order it and return within the week, and you’ll know the schedule before we leave the first time.
We keep the common fail points on the truck: handles, deadbolt cassettes, rollers, hinges, and sweeps that match the most popular CWS entry and patio series in Miami Gardens. Odd-sized glass inserts and full multi-point assemblies for older CWS models sometimes need to be ordered, typically arriving within a week. We also work with compatible parts from Andersen, and Pella when OEM CWS parts are discontinued or backordered. Call (386) 516-5343 with your model number, and we can often tell you same-day whether the part is one we carry.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Miami Gardens and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.